-
Politics are not permitted. There's plenty of places to discuss that elsewhere, and a hot pepper forum is not the place. Thank you for respecting the community!
hobbies New aquarium!
- Thread starter Uncle Eckley
- Start date
Uncle Eckley
Extreme Member
Gettin' there!
Uncle Eckley
Extreme Member
Little light leak where the canopy lid warped. Need to add a little more foam strip.
Working on assembling the plumbing.
Working on assembling the plumbing.
Last edited:
Uncle Eckley
Extreme Member
Two drains and a return.
Uncle Eckley
Extreme Member
Check out how this cheap little lamp lights up the plastic. The fish ought to really zing.
I only just noticed Charlie Beans poked into the shot, lol.
I only just noticed Charlie Beans poked into the shot, lol.
Last edited:
Uncle Eckley
Extreme Member
Stand floor cut and siliconed into place. Huge PIA. This stand is really short.
Uncle Eckley
Extreme Member
Still need to:
Drill the display
Paint the display
Cut plumbing slot in stand
Prime and paint stand and canopy
Weatherstrip canopy lid
Cut and install stand floor
Form and install overflow box
Plumb the system
Cut sump lid
Leak test
Scrub rocks
Rinse sand
Create aquascape
Cycle system (takes a couple/few weeks)
Paint the display
Cut plumbing slot in stand
Prime and paint stand and canopy
Weatherstrip canopy lid
Cut and install stand floor
Form
Plumb the system
Leak test
Scrub rocks
Rinse sand
Create aquascape
Cycle system (takes a couple/few weeks)
Uncle Eckley
Extreme Member
Nah, each beer celebrates the last one.
I'm off to pick up fresh plumbing cement here in a bit. Hope to fill and start cycling tomorrow.
Last edited:
Uncle Eckley
Extreme Member
The place was closed. Apparently it's Sunday over there in York county. So tomorrow plumbing, fill Tuesday now.
Tinkerbelle
Extreme Member
it's getting closer and closer to fishy time 
Uncle Eckley
Extreme Member
Got the cement this morning. Could put a few pieces together, but I need a nap. Backed the car into the driveway to finally pull out the rocks. I corrected my tire pressure instead and forgot all about the rocks until now. The dash wouldn't show me the tire pressure with the lid open, so I couldn't see the rocks anymore.
Uncle Eckley
Extreme Member
Okay, got all the plumbing installed. Now a nap.
Uncle Eckley
Extreme Member
The sump lid fits!
Leak test underway.
Leak test underway.
Uncle Eckley
Extreme Member
Now that I've got the sump in place I wish I'd cut the lid like this. Maybe I'll get a new piece of acrylic and make another one. That can be done any time, though - just drain the sump enough to slide it aside.
I found a good price and ordered a new piece. I may just fill the system with the sump shifted over like this and just do without a lid until the new one's ready.
I found a good price and ordered a new piece. I may just fill the system with the sump shifted over like this and just do without a lid until the new one's ready.
Last edited:
@Uncle Eckley are you using SOLIDWORKS for your 3D modeling?
Uncle Eckley
Extreme Member
Yep.
Uncle Eckley
Extreme Member
Leak test is successful. I'll probably wait until my fill hose arrives tomorrow to drain it. Then overflow wall. Can fill for real 24 hours after the overflow is installed.
Uncle Eckley
Extreme Member
I installed the overflow wall at 10:30 this evening. I suck at caulking; I hope it doesn't look too bad. Final assembly and maybe sand rinse tomorrow!
Still need to:
Drill the display
Paint the display
Cut plumbing slot in stand
Prime and paint stand and canopy
Weatherstrip canopy lid
Cut and install stand floor
Form and install overflow box
Plumb the system
Cut sump lid
Leak test
Scrub rocks
Rinse sand
Create aquascape
Cycle system (takes a couple/few weeks)
Still need to:
Paint the display
Cut plumbing slot in stand
Prime and paint stand and canopy
Weatherstrip canopy lid
Cut and install stand floor
Form and install overflow box
Plumb the system
Cut sump lid
Leak test
Scrub rocks
Rinse sand
Create aquascape
Cycle system (takes a couple/few weeks)
Last edited:
Uncle Eckley
Extreme Member
This plastic grid distributes the weight of the rock and prevents pressure points on the bottom pane. I'll fill it tomorrow. I'm too tired to mess with plumbing and I don't want to rinse sand in the dark.
